Accessories and automation Breezart TPD-283U, VAV-DP, JL201, etc.

The TPD-283U remote control with a color touch screen is included as standard in the supply and supply-exhaust Breezart units. The remote control is designed for installation in a double podrozetnik for brick or concrete PE000031 or podrozetnik for hollow walls PE030041 (other types of podrozetnik may not be suitable due to the shape of the interior space). The remote control can also be installed in a wall mounting box.

EWB-T28 - the overhead box for TPD-283U allows you to install the TPD-283U remote control on the wall surface.

The Breezart RC and Breezart MRC remote control programs allow you to control ventilation installations over an Ethernet network using the standard TPD-283U remote control. Breezart RC is designed to control a single vent installation and has versions for Android and iOS platforms (available in Google Play and AppStore). The firmware version of the remote control must be at least 3.10. Breezart MRC works only on Windows and can control several vent installations (in the free version from 1 to 5 pieces). The firmware version of the remote control must be at least 4.12.

The VAV-DP kit is designed to create a VAV system based on a Breezart supply or supply-exhaust system.

The JL201 distributed control module allows you to control the valve flap using a proportional control actuator. The SB-006 regulator (potentiometer) can be used to control the module. The supply voltage is DC 24V.

The JL201DP distributed control module allows you to control the valve flap using a proportional control actuator. The SB-006 regulator (potentiometer) can be used to control the module. The supply voltage is DC 24V.

PL302 is a remote control and data acquisition module that allows you to configure and update the firmware of the vent installation controller via the Internet. The PL302 allows you to store data coming from devices on an SD card and, if necessary, also transmit them over TCP/IP networks.

The CB-02 24V — 20mA valve control module allows you to control the valve flap using a proportional control actuator. The SB-006 regulator (potentiometer) is used to control the module. The supply voltage is DC 24V. It can transmit a 0 — 10V signal from the drive showing the current position of the flap.

The USB adapter BSA-02 allows you to connect the ventilation unit to a computer (via a USB port). The adapter is supplied with the Breezart Service Utility (BSU) program.

Hygrostat El-0206xx-RH-RH for monitoring the level of relative humidity, relay output on/off. It is used in conjunction with Breezart humidifiers (humidification sections). Color options are available: white, black, silver.

JLC100-5K regulator (potentiometer) for controlling the position of the air valve flap. It is used in conjunction with the CB-02 and JL201 modules.

The channel temperature sensor TA130 is designed to measure the air temperature in air ducts in ventilation and air conditioning systems. The mounting flange can be moved along the probe tube to adjust the depth of installation of the measuring head.

Submersible temperature sensors TW131, TW132 are designed to measure the temperature of liquids in pipelines of heating systems, heaters of ventilation systems, etc.

The SB-0034 module is a module for smoothly changing the rotation speed of a single—phase fan (with a capacity of up to 2000 m3/h). It is a transistor speed controller controlled by a 0 — 10V signal.

JL303 is an RS485 (ModBus) splitter router. The operating mode allows you to combine three different RS-485 subnets with overlapping addresses into one network, with assigning each device a unique virtual address.

The RS-485 RSCON-03 crossover module is designed to connect devices with an RS-485 interface to Breezart and Jet Logic controllers. The module allows you to switch from the RJ-14 connector to the terminals or vice versa, as well as supply power to the +24V bus.

The JLS26H sensor is a digital temperature and humidity sensor with a Modbus RTU output, a 5-meter cable with an RJ-12 connector is included for connection to the P1 port of a humidifier or vent installation. The sensor is designed to be used in conjunction with Breezart humidifiers (humidification sections) with heaters. Allows you to implement proportional control of the humidifier to accurately maintain the level of relative humidity.

• Accessories and automation. Brief characteristics.